Media Library / Images

GasGuard LPG nozzle GG20

With long connector nut to access 'hard to reach' fill points. Economic type for industrial refueling / attended refueling. Release volume on valve closure: 1,9 cm³.

TWO 100

TW coupling seal for Tank truck couplings DN 100 to EN 14420-6. NBR black.

Elaflex Pacific Pty., Australia: workshop

AMKX 50 Ms

'Camlock' brass steel coupler to EN 14420 - 7 with hose tail and Spannfix clamps

ElaSil® Silicone hose assemblies DN 13-102

For for high media purity requirements, easy to clean. Suitable for Pharma, foodstuff and cosmetics industry. Homogeneous hose construction of platinum cured, translucent and phtalate free Silicone (FDA / USP), resistant to kinking and highly flexible. Large temperature range -60° C to +200° C. Available as complete hose assembly with crimped fittings, DN 13 to 102. Here: DN 25 with Camlock Cam Locking Coupling and Triclamp connection

Elaflon PTFE 25

Rubber Expansion Joint ERV-R 80.16

RED BAND expansion joints for water, drinking water (approvalDVGW W 270 as well as ACS, conform to FDA), cold and warm waste water, seawater, cooling water, also with chemical additives for water treatment, low concentrated acids and alkalis, salt solutions, technical alcohols, esters and ketones. Can be used in oily athmospheric environments, e.g. engine rooms. Temperature (depending on medium) - 40° C up to + 100° C, temporarily up to + 120° C. Electrically dissipative.

Forklift refuelling with LPG (L.P. Gas, Autogas)

GasGuard nozzle, LPG 16 hose

M 16-1" NR cr

Female ferrule hose coupling EN 14424, factory assembled, non-reattacheable. Slimline 16 hose, blue.

Urea solution for cars and light transporters: ZVA LV for AdBlue® nozzle

Road tanker with open hose reel, HD hose assembly, ZV 500 nozzle

Hose assemblies

Polypal Clean with RMC, LPG with ACMX, Polypal Plus with SFC-SS, Tecnopal with MK-SS

Oasis BV701 Ball Valve, with air torque actuator AT101, for CNG

ELAFLEX refuelling equipment for LPG (Autogas, L.P.Gas)

UTL 50 universal hose with MannTek Dry Disconnect Coupling

ELAFLEX Hamburg

ERV flange assembly medium sizes

Fuel delivery at the petrol station

LTW 75 fuel delivery hose, GPS 50 vapour balance hose

MK-A 80 SS

MK 80 SS with active safeguard lever

DDC-V 50 SS

MannTek Dry Disconnect Coupling, DN 50, stainless steel, with BSP thread connection

Stainless steel Hose Reel spring rewind black, FEP 38, DDC-M 50 SS

Tank container filling coupling: MK 80-32 SS with VB 80 SS

MK 80-32° coupling with bent lever. For any application it should be checked that the lever can be arrested as shown even if there is tight space. Elaflex offers bent levers for all MK couplers.

LNG ship bunkering

DCC 100 Dry Cryogenic Coupling, CBC 100 PERC Cryogenic Breakaway Coupling

Stainless steel couplings with PFA coating, type "...SSE"

Surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

Universal hose assembly for vehicles fighting dangerous goods incidents:

PTFE 50, length 5 mtr., assembled with MKX 50 SS/Vi SS, VKX 50 SS/Vi SS

ELAFLEX Hamburg

Assembling ERV medium DN

SD 38 Pyropal

Steam hose with steel braids for wet saturated steam up to 18 bar (210° C) and hot water up to 120° C. For cold water up to 25 bar. Minimum burst pressure 180 bar (1 : 10 safety factor

TGN 4" Al tank truck flange with threaded nipple, VK 100 Ms male TW coupler, MB 100 Al dust cap, chain

Cabinet of road tanker:

MK 80-32 TW coupler with bent lever, VB 80 P dust plug

ELAFLEX Hamburg

Nozzle stock, ZVA Slimline 2 GR

ZH 50 nozzle with MK50SS + HD hose assembly, DDC-V 80 Ms with cap, MK 80 Ms with VB 80 P